TI811X PSP 04.07.00.01 Release Notes

TI811X PSP 04.07.00.01 Release Notes

Linux PSP

This page is currently under construction. The content of this page is due to change quite frequently and thus the quality and accuracy are not guaranteed until this message has been removed. Please feel free to contribute to this page while construction is in progress.

Important
This document covers details for Linux PSP Release 04.07.00.01.

Release Notes

04.07.00.01: August, 2012

Document License

This work is licensed under the Creative Commons Attribution-Share Alike 3.0 United States License. To view a copy of this license, visit http://creativecommons.org/licenses/by-sa/3.0/us/ or send a letter to Creative Commons, 171 Second Street, Suite 300, San Francisco, California, 94105, USA.

Read This First

PCIe: - PCIe is not supported.

Video Related

• Make sure that PIN8 of SW6 switch is turned on(to make off-chip HDMI display and EVm LCD display work).
• For Off-Chip HDMI display, on some TV's the image might be cropped(Few Lines(~15) on left and top might be missed), This is due to some TV's will do overscaling.If TV supports to disable this feature, then after disabling the video will be proper.
• Some Flashes will be seen on LCD display during power cycle. After inserting tlc59108 module, you will see Flickers, change the venc timings suitable for LCD.Refer Video Driver User Guide for more details on changing the timings.
• Off-Chip HDMI is working with only small lilliput display, samsung and philips TV, some models of Samsung may not work.

Hardware modification for Off-Chip HDMI to work with all TV's

Remove R267 and R578, and populate R264 and R579 with 10K registers

Hardware modification for 16-bit NAND

16-bit NAND is supplied with the EVM but the bus width selection switch is not populated on the EVM. By default, GPMC_D[12] is pulled down, hence corresponding to 8-bit NAND support. So, to support the NAND boot on the EVM (having 16-bit NAND), the following modification has to be done:

• Pull up GPMC_D[12]: the resistor populated at R336 should be moved to R313
  

This will set BTMODE12 to 1, which is the required configuration to support 16-bit NAND.

USB Overcurrent on USB1 port:
Please use daughter board for USB1 support, refer to TI811X known issue section [1]
GPIO

• GPIO ports from banks 4 and 5 do not have any pin control registers associated with them and hence were not added to pinmux table.
• GPIO banks 4 and 5 do not have direct interrupts, but can be configured to generate intterrupt by writing following value to A8_INT_MUX_31_28 register 0x48141614
  

The register values to be written are as shown below below

For INTH_INT_ID_GPIOINT4A 28 - 1C, INTH_INT_ID_GPIOINT4B 29 - 1D , INTH_INT_ID_GPIOINT5A 30 - 1E and INTH_INT_ID_GPIOINT5B 31 - 1F

So for GPIO 5 it should be 0x1F1E0000.

for GPIO 4, 0x00001D1C

Ethernet Switch setting
Ethernet Pins and GPMC (NOR) pins are muxed in the EVM. The mux selection can be done via combination of EVM switch setting and GPIO(Bank-5 GPIO-4).

• GP5[4] is by default low and not programmed

GPMC and EMAC Pin Mux Selection

SW10.2	GPMC/EMAC Pinout connects to
ON	GPMC
OFF	EMAC

EMAC 1 Phy power line is connected via SW7.1, to enable EMAC 1 Phy the following setting to be followed

• SW7.1 - On

The code base for Linux kernel and U-Boot included in this release is hosted at the following repositories:

Component	Repository (Branch)	Baseline Tag/Commit	Release Tag
TI81xx Linux Kernel	http://arago-project.org/git/projects/?p=linux-omap3.git;a=shortlog;h=refs/heads/ti81xx-master (ti81xx-master)	2b3ea6aa16956e15f1ba8e7b70898aaacbec2237	bb340d047a440c7deab60dad69885a4eba5ec5d7
TI81xx U-Boot	http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary (ti81xx-master)	v2010.06	113af53f577af334825b1951ea46e15e487caf5c

Additionally following patches are required on top
Uboot: http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=commit;h=e6fcefa86a70460674fe38320cc3ad1cc97a2ea6

The kernel and U-Boot have been compiled with CodeSourcery GNU Toolchain for ARM Processors 2009-q1-203 based on GCC 4.3.3

Dependencies

For complete list of components versions that will work with this release, please refer to the Software BOM page at http://processors.wiki.ti.com/index.php/Category:EZSDK_Software_BOM

This release requires following tools/packages to be installed for fbdev/v4l2 drivers:

Tool/Component	Release Version
CCS	5.0.3.00013
CGTools	4.9.2
XDC	3.23.01.43
BIOS	6.33.02.31
IPC	1.24.02.27
Syslink	syslink_2_10_07_30_eng
HDVPSS Binary	01.00.01.43

What's Supported

The Linux PSP package supports the following components:

Boot Modes Supported

Boot Mode	Supported(YES/NO)
NAND	YES
NOR	YES
SPI	YES
SD	YES
Ethernet	NO

U-Boot Features

Feature	Supported(YES/NO)
NAND	YES
NOR	YES
SPI	YES
SD	YES
Ethernet Switch 1-Port	YES
I2C	YES

Linux Device Drivers

Driver	Supported	Remarks
DCAN	YES
NAND	YES
UART	YES
I2C	YES
NOR	YES
EDMA	YES
SPI	YES
V4L2 Capture	NO	TI811X platform has only TVP5158 decoder, and it is multichannel. V4L2 framework does not support multichannel capture.
V4L2 Display	YES
SII9022a external HDMI transmitter driver	YES
HDMI Audio	NA
AIC3106 Audio	YES
ADC3101 Audio	NA
Ethernet Switch	YES
MMC/SD	YES
Watchdog Timer	YES
GPIO	YES
AVS	NO
Pinmux	YES
USB Host	YES	HID/MSC/Audio/Video
USB Gadget	YES	CDC/RNDS/FSG
RTC	YES
CIR	NO

New in this Release

DCAN driver, RTC and USB Gadget support have been added as part of this release NOR Boot mode and Kernel support have been added as part of this release

Fixed in this Release

This section lists issues fixed in this release:

TI81XX

Issue Identifier	Issue Headline
SDOCM00089892	TI81XX: USB: video capture and play from usb camera (Logitech pro 9000) fails for 640X480 resolution
SDOCM00090443	TI814X: USB: HP DVD-RW drive connected to DM814x causes kernel crashes
SDOCM00088387	Centaurus: USB audio through aplay does not work intermittently when stopped (by control-c) and started again
SDOCM00090821	DM814X: USB: video capture using usb logitech pro 9000 camera does not work for 1600x1200 resolution
SDOCM00090854	DM81XX: USB: musb driver shall use the non-posted read/write API for all register access.

TI811X

Issue Identifier	Issue Headline
SDOCM00084027	Clock parent change is not reflected in debugfs
SDOCM00085253	Failure in invoking omap2_clk_enable() for second time on ADPLL clocks
SDOCM00090102	Enabling mmu_ick/mmu_cfg_ick fails with timeout error
SDOCM00090376	Enabling pins with multiple entries in partition table fails
SDOCM00094090	Clock source selection mask for uart5 and 6 functional clocks is wrong
SDOCM00092768	U-Boot trace Showing device as "TI811X-GP rev 1.0", it must be "TI811X-GP rev 1.1.
SDOCM00090994	TI811X audio playback lag due to incorrect input clock frequency on TI811X EVM.
SDOCM00093647	Noise is observed for ALSA loopback when capture gain is set to > 30%
SDOCM00092767	U-boot Trace message shows it is booting from SD/MMC, but actually booting from SPI
SDOCM00093671	NAND boot not funcitonal for few of the EVMs
SDOCM00093388	Kernel boot crashes when uImage is downloaded via tftp
SDOCM00092770	[HDVPSS] Blue bar appearing at the left of HDMI TV once V4L2 is initialized.
SDOCM00093062	[HDVPSS V4L2] Video shifted left by almost 50 pixels in LCD
SDOCM00093452	[HDVPSS-V4L2] Image shifted left by ~50 pixels while displaying on LCD.
SDOCM00093453	[HDVPSS-V4L2] HDMI display not working
SDOCM00093549	HDMI display not working for particular Samsung model (Model no: LA32B550K1R)
SDOCM00093625	[HDVPSS] - Resizer functionality not working
SDOCM00093891	[HDVPSS]- Sparkles seen on off-Chip HDMI Display

Known Issues

This section lists known issues observed in this release:

TI81xx

Issue Identifier	Issue Headline	Known Workaround(s)
SDOCM00081588	TI81XX:USB: After four times insmod and rmmod of ti81xx.ko in loop causes crash in dma_alloc_free in cppi41dma driver	Remove all the modules in reverse order and insert all modules in right order again.
SDOCM00087448	TI81XX: USB_Audio : DUT hangs for 8 to 10 sec while unpluging the USB audiodevice during playback	The issue is with aplay application does not exit after device disconnect. Recommeded to stop the audio playback before unplugging of audio device.
SDOCM00088375	TI81XX: USB: (short packet issue) multiple resets occuring while creating a file on HP flash disk.	Known Issue, SW workaround patch available, but not complete solution.
SDOCM00091461	USB: CPPI41DMA: TX DMA generates the early completion interrupt before last byte from endpoint TxFifo is transferred out.	Known Issue, SW workaround patch available.
SDOCM0086738	Extra IN token issue: While file transfer thru usbwifi client dongle to tftp server & do i/o on HDD, intermittent usbreset occurs	Known Issue, SW workaround available. Configuring the rx transfer in transparent DMA mode and handling the data toggle appropriately.
SDOCM0091179	DM814X: USB: MUSB interrupt during DMA transfer without appropriate cause of interrupt	Known Issue, no workaround
SDOCM00086741	DM81XX: USB: While performing USBCV test with Remote wakeup capability(rndis) the EVM console freezes till test is completed.	None
SDOCM00084561	USB:TI81XX: Dynamic detection of USB-ID pin not working when device connected after linux bootup	Configure USBx_ID pin appropriately for host/device role. USBx_ID pin to Short (for host mode) and open (for device mode).
SDOCM00086735	TI81XX: USBOTG: The SRP (Session Request Protocol) initiated from OTG-B peripheral device is not working	None.
SDOCM00082602	SD removal while IO is in progress causes system hang	None. It is recommended not to remove the card while I/O is in progress.
SDOCM00089115	Subpage support in NAND is not implemented	None

TI811X

Issue Identifier	Issue Headline	Known Workaround(s)
SDOCM00090415	TI811X: There is continuous over current message on console from USB1 port when kernel loaded in usb host mode on TI811X EVM	Known issue: Always connect the daughter board to use USB1 port other wise to disable the USB1 port use steps in this patch. Note that this patch will not apply directly, edit the specific changes manually as mentioned in the patch.
SDOCM00093026	[HDVPSS]saMmapDisplay application hangs.	None
SDOCM00091535	Off-chip HDMI display not working with some TV's	Remove R267 and R578, and populate R264 and R579 with 10K registers.
SDOCM00093546	[HDVPSS-V4L2] Getting message "Unable to open (null)... skipping..." while doing slave loading of HDVPSS firmware.	None
SDOCM00093547	[HDVPSS] Swapping the memory for sections MC_HDVPSS_DESC & MC_HDVPSS_V4L2_FBDEF_MEM does not work	None
SDOCM00093625	[HDVPSS] - Resizer functionality not working	None
SDOCM00093728	[HDVPSS] saUserptrDisplay example is causing segmentation fault	None
SDOCM00093044	top command shows memory usage more than 100% (ie 130%) while runing qt app	None
SDOCM00093550	Connecting USB mouse post boot does not work	Need to ensure that the mini-A-cable shipped with the kit is left connected at all times. Hot plugging devices will then work.
SDOCM00093551	/proc/cpuinfo shows incorrect value(value 0) for revision and Serial no	None
SDOCM00093670	On some boards, "ECC: uncorrectable." error messages are reported for boot from NAND	Under Investigation
SDOCM00091706	[HDVPSS-HDMI] HDMI Control STOP on Disabled HDMI output causes HDMI driver to crash	None
SDOCM00092874	[HDVPSS] ioctl VIDIOC_S_CROP fails	None
SDOCM00092875	ioctl VIDIOC_S_FMT with buf type V4L2_BUF_TYPE_VIDEO_OVERLAY fails	None
SDOCM00092888	Getting kernel warning for first time while running ./saLoopBack ntsc, 2nd time onwards this message do not come	None
SDOCM00092923	VIDIOC_QUERYSTD on capture device is not working	None
SDOCM00094357	[HDVPSS] Getting errors VPSS_FVID2 timeout & VPSS_DCTRL failure while insmod vpss.ko	None
SDOCM00094358	[HDVPSS] Getting errors "notify_shm_drv_sendevent failed ...." during insmod vpss.ko	None
SDOCM00094510	Flickers observed on LCD display while booting	None
SDOCM00094511	[HDVPSS] Display is not adjusted properly on HDMI(top portion of the display are hidden looks like cropped)	None
SDOCM00094546	[HDVPSS-V4L2] PSP example application saLoopBackFbdev, saLoopBackScale, saLoopBack are not working	None

Installation and Usage

Please look for detailed installation and usage instructions in the User Guide

Upgrade and Compatibility Information

To upgrade to new PSP release, simply delete the old release and extract the new release in its place.

Device Support

This release supports following setups

• TI811x EVM

Validation Information

This release is tested on

TI811x Base EVM with ARM running @600MHz and DDR @400MHz

Versioning

This is 04.07.00.01 release of TI81XX Linux PSP product.

Useful Links

TI811X PSP Kernel User Guide
TI811X PSP 04.07.00.01 Feature Performance Guide/DataSheet
PSP 04.07.00.01 Release Download Page

Technical Support and Product Updates

For further information or to report any problems, contact http://community.ti.com or http://support.ti.com.

OMAP Linux Mailing List: http://vger.kernel.org/vger-lists.html#linux-omap </div>