NOTICE: The Processors Wiki will End-of-Life on January 15, 2021. It is recommended to download any files or other content you may need that are hosted on processors.wiki.ti.com. The site is now set to read only.
CC3100 & CC3200 FTDI Flashing
Contents
Instruduction[edit]
All new boards should already have the correct FTDI templates flashed into the FTDI chips. However, if your board is not recognized, installing the driver from the SDK is not working, or the built-in FTDI template is corrupted, you'll need to flash the FTDI chip again.
The software used here is FT_PROG, which you can obtain directly from the FTDI website.
Downloads[edit]
FT_PROG EEPROM Programming Utility[edit]
FT_PROG is a free EEPROM programming utility for use with FTDI devices. It is used for modifying EEPROM contents that store the FTDI device descriptors to customize designs.
Note: FT_PROG requires the Microsoft .NET Framework 4.0 installed on your system to run the application. This can be obtained from the Microsoft Website. If your system does not have .NET 4.0 installed please download the file from the above link. To install, double click on the dotnetfx.exeCode and follow the instructions in the wizard.
The latest can be obtained from FTDI utilities.
FTDI D2XX Driver[edit]
Please download the appropriate driver based on your system configuration.
FTDI Templates[edit]
| Template | Readme File |
|---|---|
| CC3100/EMU Boosterpack | |
| CC3200 Launchpad |
FTDI drivers[edit]
The FTDI drivers are part of the SDK released. Refer to the download page for access to the SDK release.
CC3100/CC3200 FTDI Programming Steps[edit]
If your CC3100/CC3200 is not recognized, install the FTDI D2XX driver.
- Install the the FT_PROG
- Connect the USB cable between the PC and your target board.
- Install either CC3200_SDK and/or CC3100_SDK package, depending on what platform you are using.
- Open FT_PROG and press F5 (or refresh) to refresh the list of connected FTDI devices.
- Right click the device and select erase.
- Right click the device choose Apply Template -> From file and choose the corresponding .xml template file from the download section above.
- Press Ctrl+P
- Reset board by unplugging and plugging USB cable.
Links[edit]
{{#invoke: Navbox | navbox }}
|
{{
Please post only comments related to the article CC3100 & CC3200 FTDI Flashing here. |
Keystone=
Please post only comments related to the article CC3100 & CC3200 FTDI Flashing here. |
C2000=For technical support on the C2000 please post your questions on The C2000 Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | DaVinci=For technical support on DaVincoplease post your questions on The DaVinci Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | MSP430=For technical support on MSP430 please post your questions on The MSP430 Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | OMAP35x=For technical support on OMAP please post your questions on The OMAP Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | OMAPL1=For technical support on OMAP please post your questions on The OMAP Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | MAVRK=For technical support on MAVRK please post your questions on The MAVRK Toolbox Forum. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here. | For technical support please post your questions at http://e2e.ti.com. Please post only comments about the article CC3100 & CC3200 FTDI Flashing here.
}} |
